Brite-view Air SyncHD BV-2322 User Manual Manuale Utente

0

9C. Remote Controller Unit (RCU) Instruction Note : 1. Press Power key pointed at the transmitter when system

10D. On Screen Display (OSD) vs. RCU Instruction  POWER Button (1) Press the POWER button on the RCU pointed at the Transmitter or presses

11 Press the CHANNEL button on the RCU to manually switch between wireless channels if the user experiences video noise. Press “CHANNEL” button on

123. Installation Step1: Setup the BV-2322T Transmitter with the A/V Source and the 1st HDTV Connect One High-Definition Audio/Video Source and

13Step2: Setup the BV-2322R receiver with the 2nd HDTV HDTV set Connection with BV-2322R: (1) Connect the HDMI cable to the HDMI OUT jack o

14Step3: Setup the IR Blaster Extender Cable and IR Sensor Extender Cable If necessary, connect the Infrared (IR) blaster (or sensor) Extender cab

15Step 4: Boot up the BV-2322T and BV-2322R (1) Place the two AAA batteries into the remote control. (2) After th

16 (4) If it is on Standby mode with the loop-through connection on, and the 1nd display attached to the transmitter + A/V source is on (Transmitt

17 (6) Press the SOURCE button, until you see the video being broadcasted from your A/V device. (7) If you have electronic devices s

18B. Channel Number Indicating the Wireless Frequency: WIDE mode Off Frequency [MHz] US ( DFS ) Europe ( DFS ) Japan ( DFS ) Support Region Chann

1 Table of Contents TABLE OF CONTENTS ...

19(8) If all operation is normal, the POWER LED and SOURCE LED will glow in solid blue. Please refer to the next form containing detailed LED desc

20 Note: A. If there is no signal quality shown, and the Source & Status LED is blinking in blue, the transmitter is most likely out of rang

21Step 5: For multi-room audio/video transmission or transmission between different floors, user could press the “WIDE” button on the remote con

22Step 6: Mounting the BV-2322 to the Wall (1) Refer the drawing of the bottom page that have relative position of the key holes and attach th

234. Troubleshooting Problem Solution The BV-2322 front panel power indicator (red LED) doesn't light up. • Check if the power plugs of BV-

24• Ensure the bit rate of audio from the source device can be supported by BV-2322. Please refer to the details in Chapter 6 Audio Bit Rate Suppo

255. Supported Resolution If the SOURCE LED continues to blink in blue (slower than “no signal” mode); OSD display: “No Supported Format ” and the

266. Audio Bit Rate Support  Digital Audio from HDMI inputs: Up to 6Mbit/s bit-rate support.  Support AC3 and DTS.  2-channel PCM over S

277. Product Specification General Specifications Supported Video Resolutions HDMI Input 1080p, 1080i, 720p, 576p, 480p Supported Audio Format

28

21. Important Information Please take the time to read this user manual before using the BV-2322T and BV-2322R. It contains important informat

29

3 Special Notice  Never use this product nearby an aircraft or medical facility.

4 CAUTION: Using of RF Modules in the U.S.  Any changes or modifications not expressly approved by the grantee of this device could void the

5CAUTION: Using This System in the United States  Any changes or modifications not expressly approved by the grantee of this device could void t

62. Introduction BV-2322T and BV-2322R wireless HD audio/video transmission solution allows users to place their HDTV set or projector where you w

72.2 Overview A. BV-2322T: Full HD Transmitter  Front Panel Buttons and LEDs  Power Button with LED Indicator Press to turn the transmitte

8 B. BV-2322R: Full HD Receiver  Front Panel Buttons and LEDs  Power Button with LED indicator Press to turn the receiver on and off. T